Introduction
If you gather three quotations for replacement windows, all three will quote a U-value. Two of them will probably quote different numbers for what is effectively the same product, and none of them will necessarily explain which measurement they have used. It is one of the few places in the specification where a genuinely useful piece of engineering data becomes a marketing figure.
A U-value describes how quickly heat passes through a building element. It is expressed in watts per square metre per degree kelvin — W/m²K — and it tells you how many watts of heat flow through one square metre of the window for every degree of temperature difference between inside and out. The lower the number, the slower the heat loss.
That definition is simple enough. The complications come from what is being measured, how it was tested, and whether the figure on the quotation bears any relationship to the performance you will experience once the window is in your wall. This article works through all three, so that when you compare quotations you are comparing like with like.
Quick summary
The short version
- U-value measures heat loss in W/m²K — lower is better, and it is the primary thermal performance figure in UK Building Regulations.
- Always compare whole-window U-values, not centre-pane. Centre-pane figures ignore the frame and spacer and typically read 0.2–0.5 lower.
- Building Regulations require a maximum of 1.4 W/m²K for replacement windows in England; 1.2 is a sensible practical target for good double glazing.
- U-value is one of three numbers. G-value (solar gain) and light transmittance matter just as much, and the right balance changes by elevation.
- Installation quality can undo a good U-value. Perimeter insulation and air sealing determine whether you achieve the tested figure in practice.
- Below roughly 0.8 W/m²K, further improvement in the window rarely pays back on its own in a typical UK home unless the whole fabric is upgraded.
Why this matters
Windows are usually the weakest thermal element in an external wall. A well-insulated modern cavity wall might achieve 0.28 W/m²K. Even an excellent triple-glazed window sits around 0.8 — roughly three times the heat loss per square metre. In a period London property with generous window openings, glazing can account for a quarter or more of total fabric heat loss.
That is why the U-value matters more than most homeowners assume, and also why chasing the last tenth of a point matters less than the industry sometimes implies. Moving from single glazing at around 5.0 to good double glazing at 1.2 removes roughly three quarters of the heat loss through that opening. Moving from 1.2 to 0.8 removes a further third of what remains — worthwhile, but a much smaller absolute gain for a noticeably higher cost.
The other reason it matters is comparability. Because U-value is the number every supplier quotes, it is the number most likely to be presented in its most flattering form. Knowing which measurement you are being shown is the difference between a fair comparison and an accidental one.
- Single glazing: approximately 4.8–5.8 W/m²K
- Early double glazing (1980s–90s, air-filled): approximately 2.8–3.2 W/m²K
- Standard modern double glazing: 1.2–1.4 W/m²K whole-window
- High-specification double glazing: 1.0–1.2 W/m²K whole-window
- Triple glazing: 0.7–1.0 W/m²K whole-window

Expert advice
Centre-pane, whole-window and installed performance
There are three distinct figures in circulation, and they are not interchangeable. Centre-pane U-value, often written Ug, measures heat flow through the middle of the sealed unit only. It excludes the spacer bar at the edge of the glass and the frame entirely. Because the glass is generally the best-performing part of a modern window, this figure always looks the most impressive.
Whole-window U-value, written Uw, is calculated across the entire window as installed: the glass, the edge-of-glass zone where the spacer bar creates a thermal bridge, and the frame, each weighted by the area it occupies. This is the figure Building Regulations use, the figure on a BFRC energy rating label, and the only one worth comparing between suppliers.
The difference between the two is not trivial. A sealed unit with a centre-pane value of 1.0 fitted into a modest uPVC frame with an aluminium spacer might produce a whole-window figure of 1.4. The same unit in a thermally broken frame with a warm-edge spacer might reach 1.2. Same glass, materially different windows.
Installed performance is the third figure, and no manufacturer certifies it. It reflects what happens once the window is in a real opening with a real reveal detail. A perfectly good window bedded into an uninsulated gap, with expanding foam as the only barrier and no continuous internal air seal, will lose heat around its perimeter in a way no laboratory test captures.
| Measure | What it includes | Use it for |
|---|---|---|
| Centre-pane (Ug) | Glass only, away from the edge | Comparing glass specifications in isolation |
| Whole-window (Uw) | Glass, spacer, frame, weighted by area | Comparing quotations and meeting Building Regulations |
| Installed | Whole window plus perimeter detailing | Judging real-world outcomes; never certified |

What actually drives the number down
Four things determine a window's U-value, and they contribute in roughly this order of significance. First, the glass coating. A low-emissivity coating is a microscopically thin metallic layer applied to one internal face of the sealed unit. It reflects long-wave heat radiation back into the room while allowing short-wave solar radiation in. It is the single largest contributor to modern glazing performance, and it is now standard on any reputable unit.
Second, the cavity gas and width. Argon fills roughly ninety per cent of modern sealed units and conducts heat less readily than air. Krypton performs better still and is used where the cavity has to be narrow, typically in slim heritage units, but it costs considerably more. Cavity width matters too: performance improves up to around 16mm and then plateaus, because wider cavities allow convection currents to establish inside the unit.
Third, the spacer bar. The traditional aluminium spacer that separates the panes is highly conductive and creates a cold bridge around the perimeter of every pane. Warm-edge spacers made from structural foam or stainless steel reduce that bridging, improving whole-window U-value by around 0.1 and — often more noticeably — reducing the edge condensation that forms on cold mornings.
Fourth, the frame. uPVC frames gain performance from multiple internal chambers and, in higher specifications, foam infill. Aluminium requires a polyamide thermal break separating the inner and outer faces; the depth of that break is what distinguishes a good aluminium system from a cheap one. Timber performs well naturally but depends on section depth.
- Low-E coating: the largest single improvement, now standard on quality units
- Argon fill in a 16mm cavity: the practical optimum for most double glazing
- Warm-edge spacer: roughly 0.1 off the whole-window figure and much less edge condensation
- Thermally broken or multi-chamber frame: determines how much of the glass performance survives
The two numbers that sit alongside it
Specifying on U-value alone produces uncomfortable rooms. The second number is the g-value, sometimes called solar factor, which describes the proportion of solar energy that passes through the glass. A g-value of 0.6 means sixty per cent of incident solar energy enters the room. High solar gain is free winter heating on a south-facing elevation and an overheating problem in a west-facing garden room in July.
The third is light transmittance, written LT, which is the proportion of visible daylight that passes through. Heavily coated solar control glass can reduce light transmittance to fifty per cent or below, which in a north-facing room already short of daylight makes the space perceptibly gloomier without providing any benefit, because there is little solar gain to control in the first place.
The sensible approach is to specify by elevation rather than applying one glass specification across the whole house. North-facing openings want the best available U-value with the highest light transmittance and no solar control. South and west-facing openings, particularly large ones and anything glazed into a roof, want solar control glass accepting a slightly higher U-value in exchange.
This is the kind of decision that is straightforward when someone walks the property with you and impossible to make sensibly from a price list. It costs nothing to specify well and a great deal to retrofit blinds and cooling to a room that was glazed without thought.
What Building Regulations require
In England, Approved Document L sets the standard for replacement windows and doors. Since June 2022, replacement windows must achieve a whole-window U-value of 1.4 W/m²K or better, or a Window Energy Rating of Band B or above. Replacement doors must achieve 1.4 W/m²K. Rooflights are assessed slightly differently, with a 2.2 W/m²K threshold reflecting the more demanding geometry.
These are minimums, not targets. Any competent installer should be offering products comfortably inside them, and most quality double glazing now sits at 1.2 or better as standard. If a quotation is quoting exactly 1.4, it is worth asking what the upgrade to 1.2 costs — it is often a small proportion of the total.
Compliance has to be certified. Either the installation is registered under a competent person scheme such as FENSA or CERTASS, or it is signed off by building control. That certificate is what your solicitor's searches will look for when you sell, so it is worth keeping safe.
Where the improvement stops paying for itself
Heat loss through a window is proportional to its U-value, so the savings from each improvement shrink as the number falls. Going from 5.0 to 1.4 removes around seventy per cent of the loss. Going from 1.4 to 1.2 removes a further four per cent of the original figure. Going from 1.2 to 0.8 removes another eight per cent of the original. Each step costs more than the last and returns less.
That does not make triple glazing pointless — far from it. It makes the case for triple glazing rest on comfort, acoustics and condensation resistance rather than on payback arithmetic. If a room has floor-to-ceiling glazing facing a cold northern aspect, the surface temperature of the glass is what determines whether the seating area next to it is usable in January. Triple glazing raises that surface temperature noticeably.
Where we would usually advise against spending the difference is a modest window in a well-heated room in an otherwise uninsulated house. In that property, the same money spent on loft insulation, draught-proofing and cavity fill will do considerably more for both bills and comfort. Beautiful homes begin with better advice, and sometimes better advice is to spend the budget elsewhere.

Common mistakes
Comparing a centre-pane figure against a whole-window figure
Ask every supplier to state Uw, the whole-window value, on the quotation, along with the frame system it applies to. If a quotation shows a strikingly low number with no frame reference, it is almost certainly a centre-pane figure.
Specifying one glass across the whole house
Set the specification elevation by elevation. Maximum clarity and lowest U-value on north-facing openings; solar control on large south and west-facing glazing and on anything in a roof.
Treating U-value as the only measure of a good window
Look at g-value, light transmittance, acoustic rating and security specification together. A window that scores brilliantly on one and poorly on the others is a compromise dressed up as a headline.
Ignoring the installation detail
Ask how the perimeter gap will be insulated and sealed, and whether the internal air seal is continuous. A tested 1.2 window installed badly performs like a 1.6 one, and no certificate will show it.
Buying triple glazing on payback grounds
Specify triple glazing where comfort, noise or condensation justify it — large glazed areas, cold aspects, busy roads. If the case rests purely on energy savings in a modest opening, the arithmetic rarely supports it.
Frequently asked questions
What is a good U-value for a replacement window?+
Building Regulations in England currently require replacement windows to achieve a whole-window U-value no worse than 1.4 W/m²K. Good quality double glazing typically lands between 1.2 and 1.4, high-specification double glazing between 1.0 and 1.2, and triple glazing between 0.7 and 1.0. Anything below 1.0 is genuinely high performance for a domestic replacement window.
Is a lower U-value always better?+
Lower means less heat escapes, so in isolation yes. But U-value is only one of three numbers that decide comfort. A very low U-value achieved with a heavily coated glass can reduce solar gain and light transmission, which on a north-facing elevation makes a room darker and no warmer. The right specification balances U-value, g-value and light transmittance for each elevation.
What is the difference between centre-pane and whole-window U-value?+
Centre-pane U-value measures only the middle of the glass, away from the spacer bar and frame. Whole-window U-value accounts for the glass, the spacer, the frame and the junctions between them, weighted by area. Whole-window is always the higher, less flattering and more honest number — it is the one Building Regulations use and the one you should compare.
Why do two quotations quote different U-values for the same glass?+
Almost always because one is quoting centre-pane and the other whole-window, or because the frames differ. The same sealed unit fitted into a slim aluminium frame and into a thermally broken multi-chamber uPVC frame will produce two different whole-window figures. Ask both suppliers to state which measure they are using and for what frame.
Does the installation affect the U-value I actually get?+
Yes, significantly. A window with a certified whole-window U-value of 1.2 that is fitted with an unsealed or poorly insulated perimeter will underperform that figure in your wall. The reveal detail, the insulation behind the frame and the internal air seal all matter. This is why installation quality is worth as much scrutiny as the product specification.
Do I need to replace windows that already meet the old standard?+
Not necessarily. If your existing double glazing is around fifteen years old, sealed, operating well and has no misting, the gain from replacement may be modest. We will tell you when repair or a sealed unit swap is the better value decision — the honest answer is sometimes that your windows have life left in them.
Related products









