Introduction
Of all the maintenance tasks in this section, lubricating hardware is the one homeowners are most likely to skip, because a slightly stiff handle or a friction stay that needs a firmer push does not feel urgent. It rarely is urgent in the early stages — but it is also one of the cheapest and quickest pieces of maintenance available, and neglecting it is what turns a five-minute job into a hardware replacement a few years later.
The confusion usually starts with product choice. Hinges, friction stays and locking gearboxes all move, but they move in different ways under different loads, and they do not all want the same lubricant. Using the wrong product — grease where oil is needed, or an aerosol solvent inside a cylinder — can do more harm than doing nothing at all, which is part of why this task gets avoided.
This guide sets out exactly what to use where, what to avoid and why, a simple twice-yearly routine that takes less time than most people expect, and how to tell the difference between a window that needs lubricating and one that needs adjusting or repairing — because oil will not fix a hinge that has dropped out of alignment.
Quick summary
The short version
- Use light machine oil or silicone lubricant on hinges, friction stays and shootbolt gearing.
- Use a PTFE-based dry lubricant on euro cylinders and multi-point locks, not oil or WD-40.
- Avoid grease on friction stays — it increases uneven resistance and attracts grit.
- A twice-yearly routine, spring and autumn, is sufficient for most homes; coastal properties benefit from more frequent attention.
- Sudden or uneven stiffness usually points to misalignment, not lack of lubrication.
- Persistent stiffness, a loose handle or a lock not engaging cleanly warrants an engineer, not more oil.
Why this matters
Window and door hardware is one of the few genuinely mechanical parts of a modern glazing installation. The frames and glass are largely static once fitted; the hinges, stays, handles and locking gear are the components doing physical work every single time a window is opened or a door is locked, which over the course of a year adds up to thousands of individual movements per opening.
Left dry, metal-on-metal or metal-on-nylon contact points wear at an accelerated and uneven rate, and the resulting play in the mechanism is what eventually shows up as a handle that needs lifting to operate, a stay that will not hold a window open, or a multi-point lock that catches on one point but not another. Almost all of this wear is preventable with a lubrication routine that costs a few pounds a year and takes perhaps twenty minutes across the whole house.
The financial case is straightforward: a bottle of the correct lubricant costs a fraction of a single hardware replacement, let alone the cost of a full sash or door being taken out of use because its locking gear has failed. This is one of the rare pieces of home maintenance where the effort involved is genuinely disproportionate to the value it protects.
- Hardware is the only genuinely mechanical part of a modern window or door installation
- Dry contact points wear unevenly and accelerate, rather than simply slowing down gently
- A correct twice-yearly routine costs very little in time or product
- Ignoring stiffness for years is what eventually turns into a hardware replacement bill

Expert advice
The right product for each mechanism
Friction stays — the arms that hold a casement window open at an angle — should be treated with a light machine oil or a silicone-based lubricant applied sparingly at the pivot points, where the arm folds and where it meets the frame track. These pivots are usually the source of a stiff-feeling stay long before the sliding channel itself is the problem, so start there rather than dousing the whole arm.
Hinges, whether traditional butt hinges on a timber door or the flag hinges common on modern uPVC and aluminium casements, take the same light oil approach. A drop at each knuckle, worked through by opening and closing the window or door a few times, is normally all that is needed. Flag hinges with an adjustment screw should be checked for correct alignment at the same time, since a hinge that has dropped slightly will feel stiff regardless of how well lubricated it is.
Espagnolette and shootbolt locking gear — the mechanism that drives multiple locking points up and down a door or window sash from a single handle — benefits from a light oil applied along the visible faceplate where the moving bolts protrude, worked in by cycling the handle through a full lock and unlock several times. This is the mechanism most likely to be neglected because it is the least visible, tucked inside the frame rebate, yet it is doing the most physical work of any hardware in the house.
Euro cylinders and multi-point lock gearboxes are the one place oil is the wrong choice. A dry PTFE-based lubricant, applied directly into the keyway and worked through with the key, lubricates the pins without leaving a residue that attracts dust and grit. Oil-based products can migrate into the cylinder over months and gradually gum up the fine tolerances inside, which is precisely the opposite of what a lubricant is meant to achieve.
| Component | Recommended product | Avoid |
|---|---|---|
| Friction stays | Light machine oil or silicone spray at pivots | Heavy grease |
| Hinges (butt and flag) | Light machine oil at each knuckle | Thick grease, which attracts grit |
| Espagnolette / shootbolt gearing | Light oil along the faceplate, worked in with the handle | Leaving it untouched because it is hidden |
| Euro cylinders and gearboxes | PTFE-based dry lubricant in the keyway | WD-40 or general oil-based sprays |

What not to use, and why it causes more harm than good
WD-40 and similar general-purpose aerosol sprays are the most common product misused on window and door hardware, largely because they are already in most homes and marketed broadly enough to seem like a universal fix. They are, strictly speaking, water displacers and light solvents rather than long-term lubricants, and their thin carrier fluid evaporates relatively quickly, leaving less protection behind than a proper lubricant would.
Used on a euro cylinder, this evaporation effect is a genuine problem: the spray can temporarily flush out whatever finer lubricant is already inside the cylinder, feel effective for a few days, and then leave the mechanism drier and grittier than before. This is why locksmiths consistently recommend against it for cylinders even though it is the product most people reach for first.
Heavy grease is the equivalent mistake on friction stays and sliding tracks. It feels like it should provide more lasting lubrication than a thin oil, but its thickness increases resistance unevenly across the arm's travel and acts as a magnet for airborne dust and grit, which then gets worked into the mechanism as an abrasive paste rather than staying on the surface as a lubricant. A thin, light oil applied more frequently achieves a far better result than grease applied once and left.
Household cooking oils or general-purpose lubricating oils not designed for exposed outdoor hardware are best avoided too, since many break down or turn tacky with UV and temperature cycling in a way purpose-made products are formulated to resist.
A simple twice-yearly routine
The most effective routine is also the least complicated: once in spring and once in autumn, work through every window and external door in the house, opening and closing each one and noting anything that feels stiffer or looser than it did the previous time. This comparison across visits is genuinely useful — it is far easier to notice a gradual change than to judge stiffness in isolation on a single occasion.
For each opening, apply light oil to the hinge or stay pivots, cycle the handle through its full range several times to work the lubricant into the espagnolette gearing, and treat any cylinder with a PTFE lubricant rather than oil. This whole process takes a few minutes per opening and considerably less time than it takes to describe.
Autumn is worth treating as the priority visit if only one can be managed each year, since it prepares hardware for the heavier use and harsher conditions of winter, when doors are opened and closed more forcefully against wind and stiff seals are more noticeable in cold weather. Coastal properties, or homes within a mile or two of the sea, should shorten this interval to roughly every three to four months, since salt-laden air accelerates corrosion on exposed metal components noticeably faster than an inland environment.
Misalignment versus lack of lubrication: telling the two apart
Not every stiff window or reluctant lock is a lubrication problem, and treating a misalignment issue as a lubrication issue simply delays the correct fix while the underlying wear continues. The key distinguishing signs are how the stiffness developed and whether it is even across the whole mechanism or concentrated at one point.
A gradual, even stiffening across the whole range of a hinge, stay or lock — the window simply feels a little heavier to open than it did last year, uniformly — is the classic signature of a lubrication issue, and it usually resolves cleanly with the routine described above. A sudden change, or stiffness that is worse at one point in the swing than another, or a door that has started catching on the frame at the top corner, points instead to misalignment: a hinge that has dropped slightly under the weight of the sash over years, or a frame that has moved fractionally as the building has settled.
Multi-point locks give a particularly clear signal when the problem is alignment rather than lubrication: if the handle only lifts and locks cleanly when the door is pulled firmly shut first, but resists or will not engage at all if the door is left to sit naturally, that is a keep or hinge adjustment issue, not something a lubricant will resolve, however liberally it is applied.
When to stop and call a specialist
Lubrication is genuinely a task most homeowners can do safely and effectively themselves, and doing it regularly is one of the best-value maintenance habits available. But it has limits, and pushing past them by applying more product or more force risks turning a straightforward adjustment into a hardware replacement.
Call a specialist if stiffness does not noticeably improve after a couple of proper lubrication attempts, if a handle feels loose at its base or requires increasing force to operate, if a multi-point lock engages at some points on the frame but not others, or if a window or door has developed a visible gap or misalignment against its frame. All of these point to wear or movement in the mechanism or the frame itself rather than a simple lack of oil.
It is also worth calling a specialist promptly rather than living with a partially working lock for security reasons — a multi-point lock that only engages one or two of its points, even if it still turns the key, is offering meaningfully less security than it is designed to provide, and this is not a situation to leave unresolved for cost reasons alone.

Common mistakes
Using WD-40 or a general aerosol spray on a euro cylinder
Use a dedicated PTFE dry lubricant in the keyway instead, worked through with the key several times.
Greasing a friction stay to make it feel smoother
Use a light oil sparingly at the pivots only. Grease increases uneven resistance and attracts grit into the mechanism.
Ignoring hardware because nothing feels obviously wrong
Lubricate on a fixed twice-yearly schedule regardless of how the hardware currently feels — prevention is the whole value of the routine.
Treating sudden or uneven stiffness as a lubrication problem
Note whether the change was gradual and even, or sudden and localised. The latter usually means misalignment and needs an engineer, not more oil.
Continuing to force a multi-point lock that only partially engages
Stop and call a specialist. A partially engaging lock is a security issue as well as a mechanical one, and forcing it risks further damage.
Frequently asked questions
What lubricant should I use on window and door hardware?+
A light machine oil, such as a general household 3-in-1 oil or a proper silicone-based lubricant, is right for friction stays, hinges and shootbolt gearing. For euro cylinders and multi-point locking mechanisms, use a PTFE-based dry lubricant rather than an oil, since oil attracts dust and grit inside the cylinder over time and eventually gums up the pins.
Can I use WD-40 on my door lock?+
It is best avoided on cylinders. WD-40 is primarily a water displacer and light solvent rather than a long-term lubricant, and it can wash out the finer, more suitable lubricant already inside a euro cylinder, leaving it drier than before once it evaporates. A dedicated PTFE lock lubricant is a better choice and is inexpensive.
How often should hinges and locks be lubricated?+
Twice a year is a sensible routine for most homes — once in spring and once in autumn — with an additional check on any window or door that gets particularly heavy daily use, such as a back door used constantly by a family. Coastal properties benefit from a slightly more frequent routine because salt air accelerates corrosion.
My window feels stiff to open — is that a lubrication problem?+
Sometimes, but not always. If a window has become stiff gradually and evenly, lubrication is a reasonable first step. If it has become stiff or misaligned suddenly, or only in certain weather, it is more likely to be a hinge or frame alignment issue, and lubricant will mask the symptom without addressing the cause.
Should I grease a friction stay?+
No. Friction stays are designed to hold a window open at any angle through controlled resistance in the arm mechanism, and heavy grease increases that resistance unevenly and attracts grit, which accelerates wear. A light oil applied sparingly at the pivot points is sufficient; the sliding channel itself is usually best left dry or wiped clean rather than oiled.
When should I stop doing this myself and call an engineer?+
If lubrication does not resolve stiffness within a couple of applications, if a handle feels loose or requires noticeably more force to operate than it used to, or if a multi-point lock is not engaging cleanly in all positions, it is time to call a specialist. These are usually signs of wear, misalignment or a failing gearbox rather than a lubrication issue, and continuing to force a mechanism can turn a simple adjustment into a full hardware replacement.
Related products









