Introduction
The day your new windows and doors are fitted is, understandably, treated as the finish line. The survey is done, the deposit is paid, the disruption of installation day is over, and it is tempting to assume the product will simply take care of itself for the next two decades. In truth, the first few weeks after fitting are an active settling-in period, and the years that follow reward a small, consistent maintenance habit far more than they punish neglect outright.
None of this is complicated or time-consuming. A window or door that has been correctly specified and properly installed does not need specialist attention, expensive products or frequent visits from a tradesperson. What it needs is drainage kept clear, seals kept clean, hardware kept lubricated, and a small amount of attention paid to what the guarantee actually requires of you, because most homeowners never read that document until something goes wrong.
This guide sets out what to do in the first six weeks, a seasonal calendar you can genuinely stick to, and the handful of habits and mistakes that determine whether your guarantee is worth the paper it is printed on when you need it.
Quick summary
The short version
- Avoid solvents, abrasives and pressure washing for at least four to six weeks while sealants and finishes finish curing.
- Protective film should be removed by your installer at completion; do not scrape baked-on film yourself.
- Keep drainage slots along the bottom of the outer frame clear of debris — blocked drainage is the single most common cause of avoidable damage.
- Lubricate hinges, hinge keeps and locking mechanisms twice a year, more often in coastal or exposed locations.
- Most guarantees require evidence of basic annual maintenance; keep a simple record of what you have done and when.
- An annual walk-round inspection catches dropped sashes, perished seals and loose hardware while they are still cheap to fix.
Why this matters
Windows and doors are one of the few home improvements sold with a genuine long-term guarantee, typically ten years on the frame and mechanism, sometimes longer on the glass. That guarantee is a real financial asset, but it is conditional, not unconditional. Manufacturers write in maintenance requirements because moving parts and weather seals are consumable by design, and a product used and maintained as intended performs very differently from one that is not.
There is also a simple mechanical reality behind the advice. A hinge carrying a heavy sash, a multi-point lock cycling twice a day, and a rubber gasket compressed against wind and rain are all working components, not static ones. Left dry, dirty or slightly misaligned, wear accelerates in a way that is barely noticeable month to month but becomes a stiff handle, a draught, or a dropped sash within two or three years.
Finally, the cost asymmetry is significant. The entire annual routine described in this article takes perhaps an hour across a typical house and costs little beyond a tube of silicone-safe lubricant. The alternative — a seized mechanism, a perished seal that has let water into the wall, or a guarantee claim rejected for lack of maintenance evidence — costs a great deal more in both money and inconvenience.
- A well-maintained window or door routinely outlasts its guarantee period by a decade or more
- Most warranty claims that are rejected are rejected on maintenance grounds, not manufacturing defects
- Hardware failure is overwhelmingly the result of dirt and dryness, not product quality

Expert advice
The first six weeks: what is still settling
Installation day looks finished, but several things are still happening behind the scenes. Silicone sealant around the perimeter of the frame typically takes between one and four weeks to fully cure, depending on the product, the ambient temperature and humidity. Until it has cured, it remains vulnerable to being marked, pulled or contaminated by cleaning chemicals, even though it looks and feels solid to the touch.
Timber and composite door slabs, and factory-painted or foiled finishes on uPVC and aluminium, also benefit from a settling-in period before they meet anything more than warm water. Solvent-based cleaners, cream cleansers with abrasive particles, and anything containing bleach can strip or dull a finish that has not fully hardened, and in some cases the damage will not be reversible.
Practically, this means limiting yourself to a soft cloth and warm water with a small amount of washing-up liquid for the first month, and being gentle with anything that looks like it is still slightly tacky or has a chemical smell. It also means giving hardware a light exercise — opening and closing each window and door fully a few times over the first fortnight — so that hinges and locks bed in evenly rather than wearing a groove in one position.
If your installer left factory protective film on the frames at completion, remove it within the first few days if at all possible. Left in direct sunlight, some films begin to bond to the surface beneath them within one to two weeks, at which point removal becomes far harder and carries a real risk of leaving a residue or a mark. If film has already started to bake on, do not scrape it — contact your installer, since most will remove it safely as part of aftercare.
A seasonal maintenance calendar that actually gets used
The maintenance calendar that works is the one that survives contact with a busy household, so we suggest anchoring it to two points in the year rather than a long list of monthly tasks nobody keeps up with. Spring and autumn are natural moments: spring because it follows the worst of winter weather and precedes the season windows are used most, and autumn because it prepares the house for the wettest and coldest months.
In spring, the priority is clearing away anything winter has left behind: check drainage slots for leaf debris and grit, clean glass and frames properly for the first time since autumn, lubricate all moving hardware, and inspect seals for any hardening or cracking that occurred over the cold months. This is also the point to check that trickle vents, if fitted, are open and unobstructed ahead of the summer.
In autumn, the emphasis shifts to preparing for weather rather than clearing up after it. Clear drainage slots again — leaves are the main culprit here — check that door thresholds are draining properly, re-lubricate hardware that will now be worked harder as doors and windows close more tightly against colder air, and look at exterior sealant for any gaps that have opened up over the summer.
A halfway check in mid-winter is worth adding for anything facing prevailing weather, simply to confirm drainage has not blocked with wind-blown debris during storms. Beyond these points, a genuinely well-installed window or door does not need more frequent attention, and over-cleaning with the wrong products causes more harm than the dirt it is removing.
| Season | Priority tasks | Time required |
|---|---|---|
| Spring | Clear drainage, deep clean glass and frames, lubricate hardware, check trickle vents | 45–60 minutes |
| Mid-winter | Quick check of drainage slots after storms | 10–15 minutes |
| Autumn | Clear drainage, check thresholds, re-lubricate hardware, inspect exterior sealant | 45–60 minutes |

Drainage slots, seals and gaskets: the parts nobody thinks about
Every modern window and most doors are designed to let a small amount of water in around the outer seal during driving rain, then drain it back out again through slots cut into the bottom of the outer frame. This is a deliberate and normal part of the design, not a fault, but it only works if those slots remain clear. A build-up of leaves, moss, insect nests or simply accumulated grit will cause water to pool inside the frame instead of draining away, and over time that trapped water can migrate into the wall construction or freeze and cause damage.
Checking drainage slots takes moments — they are usually visible as small horizontal openings along the underside of the outer frame or within the sill — and clearing them requires nothing more than a soft brush or a plastic tool, never anything metal that could scratch the drainage channel.
Rubber seals and gaskets, whether the compression seal around a casement sash or the gasket around a door slab, do two things over time: they collect dirt from airborne pollution and street grime, and they gradually lose some flexibility through UV exposure and repeated compression. Wiping them with warm soapy water during your seasonal routine removes the grit that would otherwise abrade the rubber each time the window closes, and a light application of a silicone-based seal conditioner, available from most hardware suppliers, keeps them supple for considerably longer than leaving them dry.
Silicone sealant at the perimeter of frames — where they meet brickwork or render — should also be checked annually for cracking, shrinkage or gaps opening at corners. This is not decorative sealant; it is a weatherproofing detail, and a gap here is one of the most common routes for water ingress into a wall that otherwise has nothing wrong with it.
What actually voids a guarantee
Every manufacturer's warranty document contains a maintenance clause, and it is worth reading yours properly rather than assuming it says the same as everyone else's. In general terms, guarantees are voided or weakened by four categories of action: using unauthorised cleaning products, particularly anything abrasive, solvent-based or containing bleach; making unauthorised alterations to the frame, glazing or hardware, including drilling for blinds fixings through the profile or fitting additional locks not approved by the manufacturer; failing to maintain drainage and seals as described in the care instructions supplied at handover; and, in some cases, failing to have any faults reported and repaired promptly once noticed, since ignoring a known issue can be treated as contributing to further damage.
It is also common, and reasonable, for guarantees to require some evidence of maintenance if a claim is made several years into the term. This does not need to be a professional service record — a simple note of what was done and when, even in a phone notes app, is usually sufficient to demonstrate reasonable care.
One area worth specific attention is decorating. If you repaint external brickwork, render or masonry around your windows, mask the frames properly rather than relying on a steady hand, since paint on a uPVC or aluminium frame is very difficult to remove without damaging the factory finish underneath, and most guarantees explicitly exclude damage caused by decorating work.
The annual inspection: what to actually look for
Beyond the routine cleaning and lubrication, we recommend one slightly more thorough walk-round each year, ideally in autumn before the weather turns. This is the point to catch small issues while they remain small, since almost every problem that eventually requires a call-out was visible and minor for months before it became noticeable in daily use.
Check that every window and door still closes and locks smoothly without needing to be lifted, pulled or forced — any resistance suggests either a hinge that needs adjustment or, in the case of a heavy sash, some settlement that is worth having checked before it becomes a dropped sash requiring re-hanging. Check sealed units for any sign of internal misting, which indicates a failed seal and is worth reporting under guarantee promptly rather than waiting.
Check exterior sealant at the perimeter for cracking, and check that weep holes and drainage channels remain clear after a summer of pollen and debris. Finally, check door thresholds for any sign that water is pooling rather than draining, particularly after heavy rain, since a threshold that no longer drains properly is often an early sign of settlement in the surrounding step or patio rather than a fault with the door itself.
None of this requires specialist knowledge. A homeowner who spends twenty minutes doing this once a year will catch the great majority of issues before they become expensive, and will have a much easier conversation with an installer or manufacturer if a genuine warranty claim is ever needed.

Common mistakes
Cleaning new frames with abrasive or solvent-based products in the first month
Use only warm water and a mild washing-up liquid for at least four to six weeks while sealants and finishes finish curing, then move to manufacturer-approved products.
Letting drainage slots block with leaves and grit
Check and clear them twice a year as a minimum, using a soft brush rather than anything metal that could scratch the drainage channel.
Ignoring a stiff handle or a door that needs lifting to lock
Report it promptly. These are usually a five-minute hinge adjustment when caught early and a significant repair once ignored for a year or more.
Assuming the guarantee covers everything regardless of maintenance
Read the maintenance clause when the product is installed, not when you need to make a claim, and keep a simple record of what you have done.
Painting or rendering around frames without masking them properly
Mask uPVC and aluminium frames thoroughly before any exterior decorating work — paint removal from a factory finish is difficult and often causes lasting damage.
Frequently asked questions
How soon after installation can I clean the frames?+
You can clean lightly straight away with warm water and a soft cloth, but avoid any solvent, abrasive or heavy-duty cleaning product for at least four weeks. Sealants, adhesives and some factory finishes continue to cure for several weeks after fitting, and aggressive cleaning during that window can mark the surface permanently.
Do I need to remove the protective film myself?+
No. Your installer should remove all factory protective film as part of practical completion, usually on the day of fitting or the day after. If film has been left on and has begun to bake onto the frame in sunlight, contact your installer promptly rather than trying to scrape it off, since scraping can scratch the finish underneath.
What voids a window or door guarantee most commonly?+
The most frequent causes are using the wrong cleaning products, painting or applying stickers and films to the frame, altering the hardware or lock mechanism without authorisation, and failing to keep drainage slots clear so that water sits against the frame or sill. Most guarantees also require evidence of at least annual maintenance.
How often should I service the hardware?+
Twice a year is sufficient for most homes: once in spring and once in autumn. Coastal properties or homes near busy roads benefit from a quarterly check, since salt air and airborne grit accelerate wear on hinges, locks and seals.
My new windows whistle slightly in strong wind. Is that normal?+
A very faint sound in exceptionally strong gusts can be normal, particularly on large casements, but a persistent whistle usually indicates a seal that has not bedded correctly or a hinge that needs minor adjustment. It is worth raising with your installer during the settling-in period rather than living with it.
Can I pressure wash my new frames?+
We would advise against it. Pressure washers can force water past seals and gaskets that are designed to shed water, not resist it under pressure, and can strip factory finishes from aluminium and foiled uPVC. A soft brush, warm water and a cloth achieve the same result without the risk.
Related products








